Recent content by TillertheJohn | TruckMount Forums #1 Carpet Cleaning Forums

Recent content by TillertheJohn

  1. TillertheJohn

    Mytee LX Vac Motors

    funny the manual doesn't list this "vac stack filter/screen' in the exploded parts list...or am I missing it?? @Fedri @John LaBarbera Know where to purchase this and if it is made to be replaced or taken off to be thoroughly cleaned? Thank you
  2. TillertheJohn

    Mytee LX Vac Motors

    Yes thank you. I was in the tank replacing the pump out screen filter surrounding it and I think I noticed a ball that looks like it could be a ball float that effectively blocks the suction from the motors so they aren't just eating water. Of course, foam is still going to cause damage if it...
  3. TillertheJohn

    Mytee LX Vac Motors

    Hey Ive thought about getting the wanders one as its more affordable, especially over the TMF boss filter. In your opinion, does it provide noticeable improvement over the Mytee lint hog? And how about the boss over wanders? Thank you
  4. TillertheJohn

    Mytee LX Vac Motors

    Nice. Im carrying a small container of defoamer with me too now. Took me 1.5yrs to figure out smh. I think my new process will be to sprinkle some on the carpet before extracting and carry it with me to put in the hose as needed. Did you mean inline filter between wand and extractor or an...
  5. TillertheJohn

    Mytee LX Vac Motors

    Just about 2 years but only couple hundred hours which is pretty low usage right? I think foam was the culprit over time
  6. TillertheJohn

    Mytee LX Vac Motors

    Yeah my new motors I’m rocking(sucking) again ! I wonder if I figured out how and when to use defoamer earlier if I could have made them last longer. I think that’s one drawback to air hog is small waste tank so foam can be an issue.
  7. TillertheJohn

    Mytee LX Vac Motors

    anvil?
  8. TillertheJohn

    Adding an OP

    Your logic is good but I don't know if I necessarily put all of my trust in 'big business'.
  9. TillertheJohn

    Mytee LX Vac Motors

    FWIW, and as an appropriate reply to your^ post - my air hog is just shy of 2 years old. And, to be fair, im certain it has gotten a lot less usage than someone like you over that period due to being a new business.
  10. TillertheJohn

    Mytee LX Vac Motors

    For those with knowledge of the LX vac motors, specifically the airhog lx, I always had the belief that the vacs would cut-off automatically when the recovery tank got too full or when foam built up. The dealer says that ain't so, and the times the vacs 'cut-off' for me, really meant...
  11. TillertheJohn

    Mytee LX Vac Motors

    Im at the dealer and the one motor is bad as it no longer turns on. (Switch is good and the wire is getting power). They also hear 'metal-on-metal' in the other motor which seems to be from moisture getting in there and causing corrosion/rust. So we will be replacing both vac motors today.
  12. TillertheJohn

    Mytee LX Vac Motors

    No specs on the 8.4's but... Why would they stop selling the lx motors to the public?
  13. TillertheJohn

    Mytee LX Vac Motors

    Funny you say that. I talked to rep at the dealer and he suggested checking the wires at the switch also. Hopefully that's all it is. @Fedri What machine did you have with this problem?
  14. TillertheJohn

    Mytee LX Vac Motors

    Appreciate your reply, Jim. Fingers crossed.
  15. TillertheJohn

    Any ideas? Airhog lx extractor motor shutting off at end of jobs?

    Uh oh.. Because my motor turns back on after job and I only seem to experience at the end of jobs...maybe there's a saving grace in there... Ill check for loose connections...